en:bondingtrays_3d_examples
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
en:bondingtrays_3d_examples [2021/02/19 18:05] – [Table] onyxadmin | en:bondingtrays_3d_examples [2021/02/23 07:23] (current) – [Examples for Bracket Clamp Design] onyxadmin | ||
---|---|---|---|
Line 2: | Line 2: | ||
====== Modul Bonding Trays 3D - Examples ====== | ====== Modul Bonding Trays 3D - Examples ====== | ||
---- | ---- | ||
- | |||
- | ===== Examples for Bracket Clamp Design ===== | ||
- | | {{: | ||
- | | Classic sleeve (hull) for rigid material with 0 % Rotation for common pull-off direction for all brackets. | Hull für elastic material with 100 % rotation acc. to the bracket (and 50 % thickness). | Hull for very elastic material with large slot overlap and additional cap at the end of the hull | Classic Kylix ring for bracket placement. Increase the thickness for more stable 3d printing. | Hull with reduced width and short Kylix ring for better accessibility of bracket and glue | | ||
- | \\ | ||
- | |||
- | ===== Examples for Tray Design ===== | ||
- | | {{: | ||
- | | Standard tray design with block out for better fit | Tray with thinner occlusal area for easy removal. Added two bridges for optiinal cutting | ||
- | \\ | ||
===== Parameters of Bracket Clamps " | ===== Parameters of Bracket Clamps " | ||
Line 17: | Line 7: | ||
{{: | {{: | ||
- | ^ Eintrag | + | ^ Parameter |
- | | A | Overlap Slot | Height of the clamp over the slot in direction occlusal or along the bracket | + | | A | Overlap Slot | Height of the clamp over the slot in direction occlusal or along the bracket |
- | | B | Rotation | + | | B | Rotation |
- | | C | Distance to Bracket | + | | C | Distance to Bracket |
- | | D | Thickness | + | | D | Thickness |
- | | E | [[ui_m_bondingtrays_e|Height Cap]] | Height of optional cap from buccal side | 0, | + | | E | [[ui_m_bondingtrays_e|Height Cap]] | Height of optional cap from buccal side | |
- | | F | Width | Width relative to bracket for thinner hull | + | | F | Width | Width relative to bracket for thinner hull |
- | | | + | | Slot Pin-Lenght |
\\ | \\ | ||
Line 44: | Line 34: | ||
\\ | \\ | ||
+ | ===== Examples for Bracket Clamp Design ===== | ||
---- | ---- | ||
+ | | {{: | ||
+ | | Classic sleeve (hull) for rigid material with 0 % Rotation for common pull-off direction for all brackets. | Hull für elastic material with 100 % rotation acc. to the bracket (and 50 % thickness). | Hull for very elastic material with large slot overlap and additional cap at the end of the hull | Classic Kylix ring for bracket placement. Increase the thickness for more stable 3d printing. | Hull with reduced width and short Kylix ring for better accessibility of bracket and glue | | ||
+ | \\ | ||
+ | ===== Examples for Tray Design ===== | ||
+ | | {{: | ||
+ | | Standard tray design with block out for better fit | Tray with thinner occlusal area for easy removal. Added two bridges for optiinal cutting | ||
+ | \\ | ||
+ |
en/bondingtrays_3d_examples.1613754309.txt.gz · Last modified: 2021/02/19 18:05 by onyxadmin