en:to_3d
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
en:to_3d [2021/10/20 16:43] – [Icon button [View Mirror]] onyxadmin | en:to_3d [2021/10/20 17:01] (current) – [Additional settings] onyxadmin | ||
---|---|---|---|
Line 115: | Line 115: | ||
The [View] button determines whether the active 3D window should be displayed on a separate monitor in full screen and which display mode should be used for this (if supported by the hardware): | The [View] button determines whether the active 3D window should be displayed on a separate monitor in full screen and which display mode should be used for this (if supported by the hardware): | ||
- | * Monoskopisch | + | * Monoskopic |
- | * Stereoskopie: Anaglyph (Rot/ | + | * Stereoskopy: Anaglyph (Rot/ |
- | * Stereoskopie: Checkerboard | + | * Stereoskopy: Checkerboard |
- | * Stereoskopie: Interlaced | + | * Stereoskopy: Interlaced |
- | * Stereoskopie: OpenGL Quadpuffer | + | * Stereoskopy: OpenGL Quadpuffer |
- | * Stereoskopie: Side-by-Side | + | * Stereoskopy: Side-by-Side |
- | * Stereoskopie: Epson Moverio | + | * Stereoskopy: Epson Moverio |
In addition, when a stereoscopic display is selected, the stereo effect can be adjusted using a slider or reset to default.\\ | In addition, when a stereoscopic display is selected, the stereo effect can be adjusted using a slider or reset to default.\\ | ||
Line 127: | Line 127: | ||
{{: | {{: | ||
---- | ---- | ||
- | ==== Icon button [Stereoskopie] ==== | + | ==== Icon button [Stereoskopy] ==== |
- | Über Taste [Stereoskopie] wird eingestellt, | + | The [Stereoscopy] key is used to set which display mode is to be used for the active |
- | * Monoskopisch | + | * Monoskopic |
- | * Stereoskopie: Anaglyph (Rot/ | + | * Stereoskopy: Anaglyph (Rot/ |
- | * Stereoskopie: Checkerboard | + | * Stereoskopy: Checkerboard |
- | * Stereoskopie: Interlaced | + | * Stereoskopy: Interlaced |
- | * Stereoskopie: OpenGL Quadpuffer | + | * Stereoskopy: OpenGL Quadpuffer |
- | Zusätzlich kann bei Auswahl einer stereoskopischen Darstellung der Stereoeffekt mittels Schieberegler angepasst oder auf Standard zurückgesetzt werden.\\ | + | In addition, when a stereoscopic display is selected, the stereo effect can be adjusted using a slider or reset to default.\\ |
+ | \\ | ||
{{: | {{: | ||
\\ | \\ | ||
\\ | \\ | ||
- | //Hinweis:// | + | //Note:// |
- | Der gewählte Stereo-Mode wird im 3D-View | + | The selected stereo mode is activated and deactivated in the 3D-View |
\\ | \\ | ||
- | ^ Stereomode | + | ^ Stereomode |
| | | | ||
\\ | \\ | ||
---- | ---- | ||
- | ==== Weitere Einstellungen | + | ==== Additional settings |
- | Zusätzlich können auf Reiter | + | In addition, on tab |3D| settings can be made for |
- | * Punktgröße | + | * Point Size |
- | * Pin-Länge | + | * Pin Length |
- | * Linienhöhe | + | * Line Height |
- | vorgegeben werden. | + | **• Point Size**\\ |
- | + | Parameter [Point size] controls the radius of the measuring point displayed as a 3D sphere in the 3D view between | |
- | === • Punktgröße === | + | |
- | Parameter [Punktgröße] steuert den Radius des als 3D-Kugel dargestellten Messpunktes im 3D-View zwischen | + | |
\\ | \\ | ||
- | + | **• Pin Length**\\ | |
- | === • Pin-Länge === | + | Parameter [Pin length] controls the distance of a measuring point displayed as a 3D sphere from its position on the respective surface between |
- | Parameter [Pin-Länge] steuert den Abstand eines als 3D-Kugel dargestellten Messpunktes von seiner Position auf der jeweiligen Oberfläche zwischen | + | |
\\ | \\ | ||
- | + | **• Line Height**\\ | |
- | === • Linienhöhe === | + | Parameter [Line height] controls the spacing of dimensions between |
- | Parameter [Linienhöhe] stereur den Abstand von Bemaßungen zwischen | + | |
\\ | \\ | ||
| | | | ||
- | | (PSPL/LH) = (1, | + | | (PS/PL/LH) = (1, |
| | | | ||
- | | (PSPL/LH) = (8, | + | | (PS/PL/LH) = (8, |
\\ | \\ |
en/to_3d.1634741018.txt.gz · Last modified: 2021/10/20 16:43 by onyxadmin